Get Creative Creative GigaWorks S Technology Speaker System User Manual. Get all Creative manuals!. User manual for the device Creative GigaWorks S Online user manual database. Second Creative GigaWorks S speaker comes in for repair Usually a parts list is available with the repair manual, however, we don’t.

Author: Mauhn Vozuru
Country: South Sudan
Language: English (Spanish)
Genre: Life
Published (Last): 20 August 2014
Pages: 149
PDF File Size: 5.16 Mb
ePub File Size: 20.13 Mb
ISBN: 925-1-38233-278-1
Downloads: 58529
Price: Free* [*Free Regsitration Required]
Uploader: Aragor

Share on Track this topic Print this topic. Nopes, I don’t have the schematics for the power amplifier boards. Cs on the PCB So hopefully it will help.


No connection at all. If both turns out OK then the fault could be from the control section mostly MCU controlled, which is much more difficult to diagnose.

Any changes or modifications not expressly approved. Dependent on mode setting. For the top layer, scrape a bit of solder resist off to creativr the hole expose some fresh copper has to be shiny.

Just PM me for details if interested Lex, Got one set of ‘s going thanks to your very detailed walkthrough but have come up against a problem with another. Per your first post I have tracked down all of the capacitors except 2x 47uF 25V, what brand did you use for this?

If that fuse blew then there must have been quite a short somewhere.

First off, the four capacitors used for the amplifier mnual section were 85C rated while the original capacitors were C rated and was oversized too tall.

Author Write something about yourself. Also these GigaWork and MegaWork speaker systems use multi-voice coil woofers which are rare and expensive. Does it still suffer from very low volume after repairs?


Alternatives would be Nichicon GU series which has lower ripple current handling Capacitor replacements Just as before, all electrolytic capacitors were replaced with proper high quality ones. Just replace what is required, and highly recommend replacing all those CapXon and Su’scon brand capacitors even if they still look good.

The clicking noise you are getting, is it from the sub, and if so can you control the volume? The T2 info should be on the transformer itself. It has been my experience that when you get to this stage, and you have some or most of the speakers back, you will likely be looking for a bad amp output Bash STA Anyway, just PM me for more details You can probably get all of these at www.

Make an “L” shape wire from any scrap leads must be of good thickness. Anyway look for a possible bad or dirty connection there and let me know what you find. I have removed all the glue and replaced all the capacitors, same ones you used in your repair.

Powered by Create your own unique website mxnual customizable templates. Is there anything what could be wrong now? Also, what type of Ceramic resistors should I get for the orange ones and the diode? In a typical personal computer installation, the.

Removal of cteative components and cleaning up degraded glue All the failed components those big CapXon HP series capacitors and blown diode were removed and degraded glue cleaned up. See attached photo of the connector. Really, very happy to have my speakers more or less working again.


For your information, when capacitors start failing their capacitance is becoming reduced.

Using multiple inputs – CREATIVE GigaWorks S750 User Manual

Full Screen Viewing – to easily view the user manual without downloading it to your computeryou can use full-screen viewing mode. By the way, what was wrong with it? Check the pins at the transformer for cold solder joints. That D12 is right after the transformer and this is a switching type power supply, thus you have to use either a schottky diode or a fast recovery diode.

Audio control pod and remote control | CREATIVE GigaWorks S User Manual | Page 7 / 12

My cousin’s Gigaworks S stopped working he had them repaired once already yesterday and he brought them to me to see gigaworis I can get it fixed. C7 is p V ac safety cap. Note the heatsink is bending backwards due to the oversized capacitors. The “second link” connected to the primary GND is only from the right photo?

At power on from remote, relay start then stops fast.

Soldering on such PCB especially dealing with damaged pads is a frustrating thing, using L connections through holes, scratching solder mask then create connections, have to be very careful. Two of the big capacitors were bulged quite significantly that they could not stand up straight on their tops.

That resistor is part of a RC snubber network around the recitfiers. Owners Instruction Manual Multi Language.